Close help

How to use this Learning Station

On this Learning Station, you can read and test your knowledge. Tap on a book to open its chapter list. In each chapter, you can take a quiz to test your knowledge.

To take tests, you must register with your email address or cell number. It is free to register and to take tests.

For help email info@bettercare.co.za or call +27 76 657 0353.

Printed books

Learning is easiest with printed books. To order printed books, email info@bettercare.co.za or call +27 76 657 0353.

Visit bettercare.co.za for information.

6A

Skills: Screening tests for HIV

Contents

Objectives

When you have completed this unit you should be able to:

Whenever possible, patients should be offered and encouraged to accept screening for HIV. An HIV rapid test can be used in any clinic, as no sophisticated equipment is required. Prior to testing, patients need to be counselled and consent must be obtained.

A. Equipment needed to perform an HIV rapid test

  1. The Abbott Determine HIV-1/2 Whole Blood Assay (or other rapid test kit). Each kit contains 10 cards with 10 tests. The Chase Buffer (2.5 ml bottle) is supplied with the kit.
  2. EDTA capillary tubes marked to indicate 50 µl, lancets, alcohol swabs and sterile gauze swabs. These are not supplied with the kit.

The kit needs to be stored at room temperature between 2°C and 30°C. Storage in a fridge is required during summer. The kit cannot be used after the expiry date.

B. The method of performing the HIV rapid test

  1. Clean a fingertip with an alcohol swab and allow the finger to dry.
  2. Remove a test strip from the foil cover.
  3. Prick the skin of the fingertip with a lancet. Wipe the first drop of blood away with a sterile gauze swab.
  4. Collect the next drop of blood with the EDTA tube. Either side of the tube can be used to collect blood. Fill the tube from the tip to the first black circle (i.e. 50 µl of blood). Avoid collecting air bubbles.
  5. Apply the 50 µl of blood from the EDTA tube onto the sample pad marked with an arrow on the test strip.
  6. Wait one minute until all the blood has been absorbed into the sample pad and then apply one drop of Chase Buffer. It is important that the bottle is held vertically (upside down) above the test strip when the drop of buffer is dropped onto the sample pad.
  7. Wait a minimum of 15 minutes and then read the results. The maximum waiting time for reading the test is 20 minutes. After 20 minutes the test becomes invalid.

C. Reading the results of the HIV rapid test

  1. Positive: A red bar will appear within both the Control window and the Patient window on the test strip. Any visible red bar in the Patient window must be regarded as positive. The result is positive even if the patient bar appears lighter or darker than the control bar.
  2. Negative: A red bar will appear within the Control window and but no red bar is seen in the Patient window.
  3. Invalid: If no red bar appears in the Control window, even if a red bar is visible in the Patient window. The result is invalid and the test must be repeated.

D. The interpretation of the HIV rapid test

The test is a specific test for HIV and will become positive when there are antibodies against HIV (the virus that cause AIDS) in the blood.

  1. A positive test indicates that a person has antibodies against HIV. Therefore the person is infected with HIV.
  2. A negative test indicates that a person does not have antibodies against HIV. Therefore the person is not infected with HIV, unless infected very recently and the HIV antibodies have not appeared yet.

E. Management if the HIV rapid test is positive

  1. Explain to the patient that the first screening test for HIV is positive but that this should be confirmed with a second test.
  2. Proceed with a second test using a kit from a different manufacturer.
  3. If the second test is also positive, the patient is HIV positive.
  4. Proceed with post-test counselling for a patient with a positive test.

F. Management if the first HIV rapid test is positive but the second is negative

  1. A blood sample for an ELISA test must be sent to the laboratory.
  2. The patient must be informed that the results of the HIV rapid tests are inconclusive and that a laboratory test is required to finally determine her HIV status.
  3. If the ELISA test is positive the patient is HIV positive (i.e. HIV infected).
  4. If the ELISA test is negative the patient is HIV negative (i.e. not HIV infected).
  5. Proceed with appropriate counselling.